Epoxy Floor Coatings in Mansfield TX - a coating that stays bonded to the slab
Peeling, stained or dusty concrete? We grind, repair and test your slab first, so the epoxy coating bonds to it and holds.
- Fully licensed and insured.
- Free quotes on site.
- We reply within 1 business day.
What goes into an epoxy floor coating in Mansfield?
An epoxy floor coating in Mansfield, TX is a resin system we lay over your concrete after grinding off the weak top layer, old coatings and curing compounds, so it bonds to a clean, dry slab and gives you a hard floor that's easy to clean.
Most people call us because a garage or shop floor is dusty, stained or peeling from an earlier coating, and they want it done right this time. A sauce is only as good as the stock under it, and a coating works the same way, so the price and the schedule mostly follow the slab: how big the floor is, how much old coating has to come off, how many cracks need filling, whether moisture shows up and which product fits how you use the space. I can tell most of that from one look at the floor, and your written estimate spells out how we'll prep it and which product we'd use.
How can you tell your concrete floor needs a coating?
Old coating peeling up
Paint or an old coating lifting in sheets, or wearing off where your tires sit, usually means it never bonded to the concrete, often because the slab wasn't ground or was holding moisture. The longer it goes, the more of it lets go, and every loose patch has to come off before anything new can stick.
Dusty, stained bare concrete
Bare concrete that leaves grit on your shoes or has soaked up oil drips is soft and open on top. Oil that sits for years works deeper into the slab, so waiting means more grinding and cleaning before a coating will hold.
Cracks and chipped patches
Hairline cracks and flaking spots usually come from the slab shifting or wearing over time. Left alone they widen and pack with dirt, and a coating laid right over them will show every line.
How we put down an epoxy floor coating
Most epoxy trouble starts under the coating, so we grind the slab, fix cracks and check for moisture before any resin comes out. Grinding with diamond tools takes off the worn top layer and any old sealer and leaves the surface rough enough for the epoxy to grab, and because it throws a lot of dust, one maker's guide requires a capable dust collector on the job. Once the floor is clean and the repairs have set, we lay the coating in the coats the product calls for and clean up after ourselves. You'll know how we're prepping your floor before you sign, because it's written into the estimate.
That same prep carries into the rest of our work. If your floor is in a shop, warehouse or restaurant kitchen, our commercial and industrial epoxy floor coatings page covers the heavier systems those spaces need, and if it's where you park, garage floor coatings goes into the finishes that handle tires and road grime.
Solid-color epoxy
One even color suits basements, workshops and laundry areas where you want a bright floor that mops up easily. It shows dust and tire marks more than a speckled finish, so it fits best where the floor stays fairly clean.
Epoxy with decorative flake
Colored chips tossed by hand into the wet base coat hide dust, small stains and the slab's flaws, and they give the floor a little texture underfoot. Most homeowners pick this one for a garage because it looks clean longer between sweeps.
Get a written prep plan and price for your epoxy floor
We reply within one business day to set a time, then I come out to look at your floor. The estimate is free, done on site and comes with no obligation.
(817) 405-3758- Based in
- Mansfield, TX 76063
- Hours
- Mon–Fri: 7 AM–10 PM, Sat–Sun: 8 AM–9 PM
What happens after you call about an epoxy floor in Mansfield?
From your first call to the final walk-through, here's how a coating job runs and who you'll be dealing with at each step.
I come look at the floor
You call (817) 405-3758 or send a message, and I come out myself to look at the floor and ask how you use the space. I check the slab for moisture, cracks and old coatings, because those decide the prep.
You get a written estimate
Your estimate explains how we'll prep the floor and which product fits, so you can see what you're paying for before you agree to anything. Ask then when you can use the floor again, since that comes from the specific product and your site conditions, and we'll pick a date that works for you.
Our crew preps and finishes
Our crew does the grinding, repairs and coating with me running the job. When it's done, I walk the floor with you before we pack up.
Why Mansfield homeowners call Bedrock Mansfield Concrete Coatings for epoxy
I see your floor in person
I come out to look at the floor myself, and our own crew does the work with me running the job. The person who sized up your slab is the one standing on it while it gets ground and coated.
In business since 2023
We've been coating floors since 2023, and I learned the trade working under a coatings installer after years cooking in restaurant kitchens. Both jobs taught me the same lesson, that the prep decides how the finish turns out.
Fully licensed and insured
We're fully licensed and insured. That matters on a job where we're running diamond grinders and handling resins inside your garage or house.
Based in Mansfield, across county lines
We're based in Mansfield, which mostly sits in Tarrant County with small parts in Ellis and Johnson counties. Whichever side of those lines your house is on, the slab gets the same prep.
On an epoxy floor, the part you can't see decides whether it holds, and I'd rather tell you a slab isn't ready than rush it. Call or send us a note and I'll come take a look.
Epoxy, garage and shop floors around Mansfield
The City of Mansfield requires permits for any construction, alteration or repair, but its list names plumbing, electrical, mechanical and irrigation work, not floor coatings, so the city's own page doesn't settle whether a coating job needs one. When there's doubt, the city points people to its Building Safety Department at 817-276-4220 or permits@mansfieldtexas.gov. When we're not sure about a job, we ask that office before we start, and if a permit is needed we take care of it.
A large share of Tarrant County's soil area is expansive clay, which swells when it's wet and shrinks as it dries, and slabs on it can shift. That's usually part of why we find cracks on floors here and on jobs in Burleson and Midlothian, and why we repair them before coating instead of hoping the epoxy hides them.
Questions about epoxy floor coatings in Mansfield
How much does an epoxy floor coating cost in Mansfield, TX?
Installed residential coating systems in the Dallas-Fort Worth area usually cost about $5 to $12 per square foot, going by prices advertised around the area. Where a floor lands in that range comes down mostly to prep, like stripping an old coating, filling cracks or dealing with moisture, along with the product and finish you choose. Your written estimate gives you our price for your floor.
What is the best way to prepare concrete for an epoxy coating?
Grinding or shot blasting, which pelts the slab with tiny steel beads, is usually the safest way, and one supplier's guide calls this kind of mechanical profiling the first choice. Acid etching can suit some coatings, but the same guide says it's hard to rinse and leaves oils and petroleum products in the concrete. We grind, and it's worth asking any contractor you're comparing how they'll prepare your floor.
What causes an epoxy floor to peel or discolor?
Moisture coming up through the slab and poor prep are the usual causes. One maker's guide says excess moisture in concrete can cause discoloration, keep the product from curing and make resin coatings peel away, which is why I check for moisture the first time I look at your floor.
Can you put epoxy over cracked concrete in Mansfield?
Yes, once the cracks are repaired, because coating straight over them leaves every line showing and a weak spot in the coating. One maker's prep sheet says cracks should be routed out, or cut open along their length, then primed and filled with epoxy crack repair material.
Should I pick epoxy or polyaspartic for my garage floor?
Polyaspartic is worth considering for a garage that gets sun or that you need back quickly, because manufacturer information describes it as rapidly curing and UV resistant, so it stands up to the sun's ultraviolet light. Those traits shape both which product suits your house and how the job gets scheduled, and your estimate says which one we'd use and why.
What safety steps come before an epoxy floor goes down?
For solvent-based coatings in an enclosed area, one maker says pilot lights and electrical switches must be turned off before and during application. The same maker says the space should have good ventilation to help clear solvents from the air, so we talk through your water heater, doors and windows before coating day.
Related services for coated concrete floors
If you run a shop, warehouse or restaurant kitchen, a commercial floor has to handle carts, spills and washdowns, so the system and prep get sized for that traffic.
Your garage takes hot tires, road grime and dropped tools, so a coating built for parking and storage there is worth a look before you pick a finish.
Cities we serve for epoxy floor coatings
Bedrock Mansfield Concrete Coatings is based in Mansfield, Texas, and we coat floors across the cities around it. The 12 cities listed here, including Kennedale and Waxahachie, each have their own page, and they're not the only places we work.
Mansfield, TX
Book a look at your epoxy floor
Call (817) 405-3758 or send the form with your floor's rough square footage and a note on cracks, oil stains or old coating, so I can bring the right tools to the first visit.