Polyaspartic Floor Coatings in Mansfield TX - a floor that bonds to bare concrete
Old sealer peeling, tire marks lifting or concrete dusting up? We strip it, grind it and lay down a hard polyaspartic coat that holds.
- Fully licensed and insured.
- Free quotes on site.
- We reply within 1 business day.
Is a polyaspartic coating right for your concrete floor?
Polyaspartic floor coatings in Mansfield, TX are a fast-setting resin we roll over ground, cleaned concrete, so your garage, shop or patio ends up with a hard, glossy floor that wipes clean instead of soaking up oil and dust.
Most calls start with a garage that's been bare or sealed for years and is starting to look tired, and the owner wants it back in use without losing the car to the driveway for long. The price moves with the size of the floor, how much old sealer or coating has to come off, how many cracks need filling and the finish you pick. The schedule turns mostly on the slab itself, meaning how much moisture it holds, whether it's new concrete still curing, and the weather that week. I can't tell you which of those apply until I've seen your floor, so your written estimate explains how we'd prep it and which product fits.
How do you know your concrete floor is ready for a new coating?
Old sealer peeling up
White patches or flakes lifting at the edges usually mean the old sealer lost its grip, often from moisture or a weak first bond. The longer it goes, the more loose film there is to strip, and anything new put over it would let go right along with it.
Tire marks pulling the coat
Dark tracks or bare spots where you park usually mean a soft coating that warm tires have been lifting a little every time you pull out. Each summer takes more of it, and patching a coating like that rarely matches or lasts.
Dust and stains on concrete
Gray powder you keep sweeping up and oil spots that won't wash out mean bare concrete is wearing and soaking in whatever drips on it. Stains get deeper the longer they sit, and deep oil takes more grinding to get out before we can coat.
How we put down a polyaspartic floor coating
I start by checking the slab for moisture, cracks and any old finish, because a coating can only be as good as what it's sitting on. Our crew takes off any old sealer first so the new coat bonds to bare concrete, then grinds the surface open, fills the cracks and vacuums every bit of dust, much like drying and seasoning a pan before anything goes in it. Polyaspartic sets up fast, so we time the coats to when the slab is cooling down instead of heating up, and that's the part most people never think about.
Polyaspartic isn't the only way to finish a slab. If you want a poured, swirled look with real depth for a living area or showroom, metallic epoxy flooring gives you that, and for a commercial kitchen that sees hot washdowns every day, urethane cement flooring handles the heat and water better than a thin coat.
Full flake broadcast
Color chips spread over the base coat and sealed under a clear topcoat suit garages and shops best, because they hide small flaws in the concrete and give tires and boots more grip than plain gloss.
Solid color or clear coat
A single color, or a clear coat that lets the concrete show through, suits laundry rooms, workshops and patios where you want a clean, even look, though it shows dust and small marks more than flake does.
Get a written polyaspartic estimate for your floor
We reply within one business day to set a time, and I come out to look at the floor myself. The estimate is free, done on site and comes with no obligation.
(817) 405-3758- Based in
- Mansfield, TX 76063
- Hours
- Mon–Fri: 7 AM–10 PM, Sat–Sun: 8 AM–9 PM
What happens when you call us about a polyaspartic floor in Mansfield?
From your first call to the last walk across the finished floor, here's how a polyaspartic job runs with us and who you'll deal with at each step.
Call or send a message
You call or fill out the form, and I come out to see the floor myself. I'll ask how you use the space and check the slab for moisture, cracks and any old coating or sealer.
Get your written estimate
Your written estimate explains how we'll prep your floor and which product fits it, so you know what you're paying for before anything starts. Once you're happy with it, we pick a date that works for you.
Our crew preps and finishes
Our crew does the grinding, cleaning and coating with me running the job. When it's done, I walk the floor with you before we pack up.
Why Mansfield homeowners call Bedrock for polyaspartic floors
The estimator runs your job
The same person who looks at your floor runs the crew that coats it, and our own crew does the work. Nothing I learn about your slab at the estimate gets lost before the work starts.
Prep comes before any coating
I'd rather tell you a slab isn't ready than rush a coat onto it, the same way a good kitchen won't plate food that isn't done. A floor that peels later isn't one I want our name on, and that's why it's satisfaction guaranteed on every job.
Licensed, insured and Mansfield based
We're fully licensed and insured, so you know who's covered while we're working on your property. I started our own shop here in Mansfield in 2023, after learning the trade under a coatings installer.
The coat is only as good as the slab under it, so the first thing I'll want is a look at yours. Tell us about your floor or call (817) 405-3758.
Polyaspartic coating jobs in Mansfield, from permits to summer heat
The City of Mansfield requires a permit for any construction, alteration or repair of a building, and questions go to its Building Safety Department at 817-276-4220. We don't guess on whether a floor coating falls under that. When we're not sure, we ask the city before we start, and if a permit's needed, we take care of it.
Heat is the bigger factor for this coating here. Mansfield's average daily highs reach 94°F in July and 95°F in August, and one product's data sheet calls for applying the coating as temperatures fall, because concrete that's warming lets trapped air escape and mar the finish. For outdoor floors like patios and pool decks, that data sheet names late afternoon as the safer time, so we plan exterior work around the day's heat, the same way we do on jobs in Midlothian and Burleson. We're based in Mansfield and work across the cities around it.
Questions about polyaspartic floors in Mansfield
How soon can I park on a polyaspartic garage floor?
One DFW coating marketplace says a polyaspartic floor is often ready for vehicles in 24 hours, compared with 3 to 5 days, including cure time, before you should park on professional epoxy. That shorter wait is the main reason people who need their garage back pick it. I'll tell you at the estimate what to plan for on your floor.
Is polyaspartic better than epoxy for a garage in Texas heat?
The same marketplace says polyaspartic resists hot-tire pickup and yellowing from sunlight far better than epoxy, and calls that a real factor in DFW summers. Hot-tire pickup is when a tire warmed by the drive softens the coating and pulls it up as you back out. If your garage door faces the afternoon sun or stays open a lot, that's worth weighing.
Why does moisture under my slab matter for a floor coating?
Water vapor coming up through the concrete can push on a coating from below. One maker's guide says a slab on grade needs a suitable moisture barrier, or seasonal ground moisture can push vapor through it, so on a slab without one, a passing test only tells part of the story. One product data sheet requires dry concrete and a moisture test before coating, so ask any installer which test they plan, and I'll tell you which one I'd run on yours.
How long do I have to wait to coat a new concrete slab?
One maker's guide says new concrete must cure at least 28 days before it's coated. If you're pouring a new garage or patio, plan the coating for after that, and call us while it's curing so we can check the slab when the time comes.
How much do polyaspartic floor coatings cost in Mansfield?
I can't give you a fair number until I've seen the floor, because the prep moves the price as much as the coating does. The size, how much old sealer has to come off, the cracks to fill, any moisture problems and whether you pick flake or a solid finish all change it. Call (817) 405-3758 and I'll come take a look.
How do I clean a new polyaspartic floor?
Wait 24 hours before using water or a neutral cleaner, and at least a week before running any mechanical cleaning equipment like a floor scrubber, according to one maker's instructions. After that, a soft mop and a mild cleaner usually keep it looking right.
Other floor finishes we put down
When a floor needs a one-of-a-kind look, with pigments poured and worked so each room turns out different, metallic epoxy is the decorative choice.
Commercial kitchens, breweries and wash bays that see scalding water, steam and harsh cleaners every day usually need urethane cement rather than a thin coating.
Service areas around Mansfield for floor coatings
Bedrock Mansfield Concrete Coatings is based in Mansfield, TX and works across the cities around it, from Kennedale to Cedar Hill. The 12 cities below each have their own page, and we work in plenty of others nearby too.
Mansfield, TX
Book a slab check for polyaspartic
Tell us the floor's age, how you use it and whether there's an old coating or sealer on it, and I'll come out knowing what to test for.